Top Quality Induction Motor And Gearbox - Closed loop motor driver-HBS86H – Longs Motor

Product Detail

Product Tags

Related Video

Feedback (2)

Our commission is to serve our users and clients with best quality and competitive portable digital products for 12v Dc Motor Controller , Nema 17 Closed Loop Stepper Motor , Dc Motor 5000rpm , Welcome to create the well and extensive standing business enterprise interactions with our business to produce a superb potential jointly. customers' pleasure is our eternal pursuit!
Top Quality Induction Motor And Gearbox - Closed loop motor driver-HBS86H – Longs Motor Detail:

1. Overview

The HBS86H hybrid stepper servo drive system integrates the servo control technology into the digital stepper drive perfectly. And this product adopts an optical encoder with high speed position sampling feedback of 50 μ s, once the position deviation appears, it will be fixed immediately. This product is compatible the advantages of the stepper drive and  the servo drive, such as lower heat, less vibration, fast acceleration, and so on. This kind of servo drive also has an excellent cost performance.

  1. Features

u Without losing step, High accuracy in positioning

u 100% rated output torque

u Variable current control technology, High current efficiency

u Small vibration, Smooth and reliable moving at low speed

u Accelerate and decelerate control inside, Great improvement in smoothness of starting or stopping the motor

u User-defined micro steps

u Compatible with 1000 and 2500 lines encoder

u No adjustment in general applications

u Over current, over voltage and over position error protection

u Green light means running while red light means protection or off line

3. Ports Introduction

3.1 ALM and PEND signal output ports

 

01

 

Port

Symbol

Name

Remark

1

PEND+

In position signal output +

+

 

 

 

 

 -

2

PEND-

In position signal output -

3

ALM+

Alarm output +

4

ALM-

Alarm output -

3.2 Control Signal Input Ports

 

01

 

Port

Symbol

Name

Remark

1

PLS+

Pulse signal +

Compatible with

5V or 24V

2

PLS-

Pulse signal -

3

DIR+

Direction signal+

Compatible with 5V or 24V

4

DIR-

Direction signal-

5

ENA+

Enable signal +

Compatible with

5V or 24V

6

ENA-

Enable signal -

3.3 Encoder Feedback Signal Input Ports

 01

 

Port

Symbol

Name

Wiring color

1

PB+

Encoder phase B +

Blue

2

PB-

Encoder phase B -

White

3

PA+

Encoder phase A +

Yellow

4

PA-

Encoder phase A -

Green

5

VCC

Input power

Red

6

GND

Input power ground

Black

3.4 Power Interface Ports

 01

Port

Identification

Symbol

Name

Remark

1

 

Motor Phase Wire Input Ports

A+

Phase A+(Red) Motor Phase A

2

A-

Phase A- (Blue)

3

B+

Phase B+(Green)

Motor Phase B

4

B-

Phase B-(Black)

5

 

Power Input Ports

VCC

Input Power +  

AC24V-70V DC30V-100V

6

GND

Input Power-

 

 4.Technological Index

Input Voltage

24~70VAC or

30~100VDC

Output Current 6A 20KHz PWM
Pulse Frequency max

200K

Communication rate 57.6Kbps
 

Protection

l Over current peak value 12A±10%

l Over voltage value 130V

l The over position error range can be set through the HISU

Overall Dimensions(mm)

150×97.5×53

Weight

Approximate 580g
 

 

Environment Specifications

Environment

Avoid dust, oil fog and corrosive gases

Operating

Temperature

70℃ Max

Storage

Temperature

-20℃~+65℃

Humidity

40~90%RH

Cooling

method

Natural cooling or forced air cooling

Remark:

 

VCC is compatible with 5V or 24V;

R(3~5K) must be connected to control signal terminal.

Remark:

VCC is compatible with 5V or 24V;

R(3~5K) must be connected to control signal terminal.

 

 

5.2 Connections to Common Cathode

04


Remark:

 

VCC is compatible with 5V or 24V;

R(3~5K) must be connected to control signal terminal.

 

 

5.3 Connections to Differential Signal

04
 

 

Remark:

VCC is compatible with 5V or 24V;

R(3~5K) must be connected to control signal terminal.

5.4 Connections to 232 Serial Communication Interface

 

 05      

PIN1 PIN6 PIN1  PIN6

Crystal Head

foot

Definition

Remark

1

TXD

Transmit Data

2

RXD

Receive Data

4

+5V

Power Supply to HISU

6

GND

Power Ground

5.5 Sequence Chart of Control Signals

In order to avoid some fault operations and deviations, PUL, DIR and ENA should abide by some rules, shown as following diagram:

Remark:

PUL/DIR

 

  1. t1: ENA must be ahead of DIR by at least 5μ s. Usually, ENA+ and ENA- are NC (not connected).
  2. t2: DIR must be ahead of PUL active edge by 6μ s to ensure correct direction;
  3. t3: Pulse width not less than 2.5μ s;
    1. t4: Low level width not less than 2.5μ s.

6. DIP Switch Setting

6.1 Activate Edge Setting

SW1 is used for setting the activate edge of the input signal, “off” means the activate edge is the rising edge, while “on” is the falling edge.

6.2 Running Direction Setting

SW2 is used for setting the running direction, “off” means CCW, while “on” means CW.

6.3 Micro steps Setting

The  micro  steps  setting  is  in  the following table, while SW3 、

SW4 SW5 SW6 are all on, the internal default micro steps inside is activate,this ratio can be setting through the HISU

8000

on

on

off

off

10000

off

on

off

off

20000

on

off

off

off

40000

off

off

off

off

7. Faults alarm and LED flicker frequency


Flicker

Frequency

Description to the Faults

1

Error occurs when the motor coil current exceeds

the drive’s current limit.

2

Voltage reference error in the drive

3

Parameters upload error in the drive

4

Error occurs when the input voltage exceeds the

drive’s voltage limit.

5

Error occurs when the actual position following

error exceeds the limit which is set by the position error limit.

  1. Appearance and Installation Dimensi
  1. Typical Connection

 

This drive can provide the encoder with a power supply of +5v, maximum current 80mA. It adopts a quadruplicated-frequency counting method, and the resolution ratio of the encoder multiply 4 are the pulses per rotate of the servo motor. Here is the typical connection of

10. Parameter Setting

The parameter setting method of 2HSS86H-KH drive is to use a HISU adjuster through the 232 serial communication ports, only in this way can we setting the parameters we want. There are a set of  best default parameters to the corresponding motor which are care

adjusted by our engineers, users only need refer to the following table, specific condition and set the correct parameters.

Actual value = Set value × the corresponding dimension

 

There are total 20 parameter configurations, use the HISU to download the configured parameters to the drive, the detail descriptions to every parameter configuration are as follows:

 

 

Item

Description

Current loop Kp

Increase Kp to make current rise fast. Proportional Gain determines the response of the drive to setting command. Low Proportional Gain provides a stable system (doesn’t oscillate), has low stiffness, and the current error, causing poor performances in tracking current setting command in each step. Too large proportional gain values will cause oscillations and

unstable system.

Current loop Ki

Adjust Ki to reduce the steady error. Integral Gain helps the drive to overcome static current errors. A low or zero value for Integral Gain may have current errors at rest. Increasing the integral gain can reduce the error. If the Integral Gain is too large, the system

may “hunt” (oscillate) around the desired position.

Damping coefficient This parameter is used to change the damping coefficient in case of the desired operating state is

under resonance frequency.

Position loop Kp

The PI parameters of the position loop. The default values are suitable for most of the application, you don’t need to change them. Contact us if you have

any question.

Position loop Ki

 

Speed loop Kp

The PI parameters of the speed loop. The default values are suitable for most of the application, you don’t need to change them. Contact us if you have

any question.

Speed loop Ki

Open loop

current

This parameter affects the static torque of the motor.
Close loop current This parameter affects the dynamic torque of the motor. (The actual current = open loop current +

close loop current)

Alarm Control

This parameter is set to control the Alarm optocoupler output transistor. 0 means the transistor is cut off when the system is in normal working, but when it comes to fault of the drive, the transistor

becomes conductive. 1 means opposite to 0.

Stop lock enable

This parameter is set to enable the stop clock of the

drive. 1 means enable this function while 0 means disable it.

Enable Control

This parameter is set to control the Enable input

signal level, 0 means low, while 1 means high.

Arrival Control

This   parameter   is   set   to   control   the   Arrival

optocoupler output transistor. 0 means the transistor is   cut   off   when   the   drive   satisfies   the arrival

 

 

 

 

Encoder resolution

 

Position error limit

 

 

 

Motor type selection

 

Speed smoothness

command, but when it comes to not, the transistor becomes conductive. 1 means opposite to 0.
This drive provides two choices of the number of

lines of the encoder. 0 means 1000 lines, while 1 means 2500 lines.

The limit of the position following error. When the actual position error exceeds this value, the drive will go into error mode and the fault output will be

activated. (The actual value = the set value× 10)

   

Parameter

1

2

3

4

5

 
 

Type

 

86J18

 

65EC

 

86J18

 

80EC

 

86J18

 

95EC

 

86J18

 

118EC

 

86J18

 

156EC

 

This parameter is set to control the smoothness of the speed of the motor while acceleration or deceleration, the larger the value, the smoother the speed in acceleration or deceleration.

 

 

0 1 2 … 10

 

 

User-defined p/r This parameter is set of user-defined pulse per revolution, the internal default micro steps inside is

activate while SW3、SW4、SW5、SW6 are all on,

users can also set the micro steps by the outer DIP switches. (The actual micro steps = the  set value

× 50)

11. Processing Methods to Common Problems and Faults

11.1 Power on power light off

n No power input, please check the power supply circuit. The voltage is too low.

11.2 Power on red alarm light on

n Please check the motor feedback signal and if the motor is connected with the drive.

n The stepper servo drive is over voltage or under voltage. Please lower or increase the input voltage.

11.3 Red alarm light on after the motor running a small

angle

n Please check the motor phase wires if they are connected correctly if not please refer to the 3.4 Power Ports

n Please check the parameter in the drive if the poles of the motor and the encoder lines are corresponding with the real parameters, if not, set them correctly.

n Please check if the frequency of the pulse signal is too fast, thus the motor may be out of it rated speed, and lead to position error.

11.4 After input pulse signal but the motor not running

n Please check the input pulse signal wires are connected in reliable way.

n Please make sure the input pulse mode is corresponding with the real input mode.

 


Product detail pictures:

Top Quality Induction Motor And Gearbox -
 Closed loop motor driver-HBS86H – Longs Motor detail pictures


Related Product Guide:
How to Troublshoot Servo Motors and Stepper Motors
3 Common Robotics Motors – Servo, DC, and Stepper Motors

Along with the "Client-Oriented" enterprise philosophy, a rigorous high-quality control process, superior production products along with a robust R&D group, we constantly deliver premium quality products, exceptional solutions and aggressive costs for Top Quality Induction Motor And Gearbox - Closed loop motor driver-HBS86H – Longs Motor, The product will supply to all over the world, such as: Swedish , Berlin , Peru , We have 48 provincial agencies in the country. We also have stable cooperation with several international trading companies. They place order with us and export products to other countries. We expect to cooperate with you to develop a larger market.
  • Customer service staff and sales man are very patience and they all good at English, product's arrival is also very timely, a good supplier.
    5 Stars By Kama from Houston - 2018.03.03 13:09
    A good manufacturers, we have cooperated twice, good quality and good service attitude.
    5 Stars By Ruby from Chile - 2018.02.08 16:45
    WhatsApp Online Chat !