Factory Cheap Hot Dapu Motor Brushless Motor - stepper motor driver-DM420A – Longs Motor

Product Detail

Product Tags

Related Video

Feedback (2)

We always stick to the principle "Quality First, Prestige Supreme". We are fully committed to providing our clients with competitively priced quality products, prompt delivery and professional service for Dc Planetary Gear Motor , Brake Motor For 3d Printer Machine , Brushless Motor 57blf01 , We sincerely welcome friends to negotiate business and start cooperation. We hope to join hands with friends in different industries to create a brilliant future.
Factory Cheap Hot Dapu Motor Brushless Motor - stepper motor driver-DM420A – Longs Motor Detail:

Introduction:

DM420A  is a type  of two-phase hybrid stepping motor driver, The drive voltage of which is from 12VDC to 36VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 20mm to 42mm outside diameter and less than 2.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM420A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.

Features:

l High performance, low price

l Average current control, 2-phase sinusoidal output current drive

l Supply voltage from 12VDC to 36VDC

l Opto-isolated signal I/O

l Overvoltage, under voltage, overcorrect, phase short circuit protection

l 8 channels subdivision and automatic idle-current reduction

l 8 channels output phase current setting

l Offline command input terminal

l Motor torque is related with speed, but not related with step/revolution

l High start speed

l High hording torque under high speed

Electrical specification:

Input voltage 12-36VDC
Input current < 2A
Output current 0.44A- 2.83A
Consumption Consumption:40W;
Temperature Working Temperature -10~45℃;Stocking temperature -40℃~70℃
Humidity Not condensation, no water droplets
gas Prohibition of combustible gases and conductive dust
weight 70G

 

Pins assignments and description:

1) Connector Pins    Configurations

 

Pin Function                 Details
PUL +,PUL- Pulse signal, PUL+ is the positive end of pulses  input pinPUL- is the negative end of pulse  input pin 
DIR+,DIR- DIR signal: DIR+ is the positive end of direction input pinDIR- is the negative end of direction input pin
ENBL+ Enable signal:  ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.
ENBL- ENBL- is the negative end of direction input pin. Usually left unconnected (enabled)

 

2) Pins wiring diagram:

PC’s control signals can be active in high and low electrical level. When the high electrical level is active, all control negative signals will be connected together to GND. When low electrical level is active, all control positive signals will be connected together to public port. Now give two examples(  Open collector &PNP), please check them:

A2

Fig 1. Input port circuit (Positive connection)

PC open connector outputA3

Fig. 2 Input port circuit ( Negtive connection)

PC PNP output

Note: When VCC=5V, R=0

When VCC=12V, R=1K, >1/8W

When VCC=24V, R=2K,>1/8W

R must connect in the control signal part .

3.Function choice ( Using DIP pins to achieve this function)

1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table: 

 

SW5 ON OFF ON OFF ON OFF ON OFF
SW6 ON ON OFF OFF ON ON OFF OFF
SW7 ON ON ON ON OFF OFF OFF OFF
Pulse/rev 200 400 800 1600 3200 6400 12800 25600
Micro 1 2 4 8 16 32 64 128

 

 

 

2) Standstill current setting

SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic current and ON meaning that standstill is set to be the same as the selected dynamic current.

3) Output current setting:

The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a setting

Closest to your motor’s required current

SW1 SW2 SW3 PEAK RMS
ON ON ON 0.44 A 0.31 A
OFF ON ON 0.62 A 0.44 A
ON OFF ON 0.74 A 0.52 A
OFF OFF ON 0.86 A 0.61 A
ON ON OFF 1.46 A 1.03 A
OFF ON OFF 1.69 A 1.20 A
ON OFF OFF 2.14 A 1.51 A
OFF OFF OFF 2.83 A 2.00 A

 

4) Semi-flow  function:

Semi-flow function is that there is not step pulse after200 ms, the driver output current automatically reduced to 40% of rated output current, which is used to prevent motor heat.

4. Pins of motor & power:

Motor and power pins

1

A+

Motors wiring

2

A-

3

B+

4

B-

5,6

DC+ DC-

Power supply Power supply :DC12-36VDCThe peak input current cannot be up to 2A

5. Mechanical Specification:

To have 20mm of space around ,cannot be placed next to other heating devices. What’s more, avoid dust, oil mist, corrosive gas, heavy humidity and high vibration. (Unit=mm)

 

A4

 

 

 

6. Adjustment of troubleshooting

1) , the status on light’s indication
PWR: green, normal work light.
ALM: red, failure light, the motor with phase short-circuit, overvoltage and under-voltage protection.

2) Troubles

Alarm indicator Reasons Measures
LED off turn Wrong connection for power Check wiring of power
Low-voltages for power Enlarge voltage of power
Motor doesn’t run, without holding torque Wrong connection of stepper motor Correct its wiring
RESET signal is  effective when offline Make RESET ineffective
Motor doesn’t run, but maintains holding torque Without input pulse signal Adjust PMW & signal level
Motor runs wrong direction

Wrong wires’ connection

Change connection for any of 2 wires

Wrong input direction signal Change direction setting
Motor’s holding torque is too small Too small relative to current setting Correct rated current setting
Acceleration is too fast Reduce the acceleration
Motor stalls Rule out mechanical failure
Driver does not match with the motor Change a suitable driver

 

7. Driver wiring
A complete stepper motor control system should contain stepper drives, DC power supply and controller (pulse source). The following is a typical system wiring diagram

A5

 


Product detail pictures:

Factory Cheap Hot Dapu Motor Brushless Motor -
 stepper motor driver-DM420A – Longs Motor detail pictures


Related Product Guide:
Basic Motion Control – An Introduction to Stepper Motors
CNC Stepper Motors

We're committed to providing easy,time-saving and money-saving one-stop purchasing service of consumer for Factory Cheap Hot Dapu Motor Brushless Motor - stepper motor driver-DM420A – Longs Motor, The product will supply to all over the world, such as: Mauritius , Serbia , Philippines , We aim to build a famous brand which can influence a certain group of people and light up the whole world. We want our staff to realize self-reliance, then achieve financial freedom, lastly obtain time and spiritual freedom. We do not focus on how much fortune we can make, instead we aim to obtain high reputation and be recognized for our products. As a result, our happiness comes from our clients satisfaction rather than how much money we earn. Ours team will do best for you always.
  • We always believe that the details decides the company's product quality, in this respect, the company conform our requirements and the goods are meet our expectations.
    5 Stars By Sabina from Latvia - 2018.07.27 12:26
    Speaking of this cooperation with the Chinese manufacturer, I just want to say"well dodne", we are very satisfied.
    5 Stars By Monica from Puerto Rico - 2017.12.02 14:11
    WhatsApp Online Chat !