Chinese Professional Stepper Motor 2 Phase - stepper motor driver-DM542A – Longs Motor

Product Detail

Product Tags

Related Video

Feedback (2)

"Based on domestic market and expand overseas business" is our development strategy for Nema 14 Stepper Motor And Driver , High Torque Motor With Driver , Closed Loop Stepper Motor , Welcomes all abroad close friends and retailers to ascertain collaboration with us. We are going to give you with genuine, high-quality and successful company to satisfy your requirements.
Chinese Professional Stepper Motor 2 Phase - stepper motor driver-DM542A – Longs Motor Detail:

Introduction:

DM542A is a type  of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, computer embroider machine, packing machines and so on.

Features:

l High performance, low price

l Average current control, 2-phase sinusoidal output current drive

l Supply voltage from 18VDC to 50VDC

l Opto-isolated signal I/O

l Overvoltage, under voltage, overcorrect, phase short circuit protection

l 15 channels subdivision and automatic idle-current reduction

l 8 channels output phase current setting

l Offline command input terminal

l Motor torque is related with speed, but not related with step/revolution

l High start speed

l High hording torque under high speed

Electrical specification:

Input voltage 18-50VDC
Input current 4A
Output current 1.0A4.2A
Consumption Consumption:80W;  Internal Insurance6A
Temperature Working Temperature -1045℃;Stocking temperature -40℃~70
Humidity Not condensation, no water droplets
gas Prohibition of combustible gases and conductive dust
weight 200G
  1. Pins assignments and description:

 

1) Connector Pins    Configurations

 

Pin Function                 Details
PUL +,PUL- Pulse signal, PUL+ is the positive end of pulses  input pinPUL- is the negative end of pulse  input pin

 

DIR+,DIR- DIR signal: DIR+ is the positive end of direction input pinDIR- is the negative end of direction input pin
ENBL+  Enable signal:  ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.
ENBL- ENBL- is the negative end of direction input pin. Usually left unconnected (enabled)

 

2) Pins wiring diagram:

PC’s control signals can be active in high and low electrical level. When the high electrical level is active, all control negative signals will be connected together to GND. When low electrical level is active, all control positive signals will be connected together to public port. Now give two examples(  Open collector &PNP), please check them:

t1

Fig 1. Input port circuit (Yang connection)

PC open connector output

 t2

                                    Fig. 2 Input port circuit ( Yin connection)

PC PNP output

 

 t2

Note: When VCC=5V, R=0

When VCC=12V, R=1K, 1/8W

When VCC=24V, R=2K,1/8W

R must connect in the control signal part .

 

3.Function choice ( Using DIP pins to achieve this function)

1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table: 

SW5

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

SW6

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

SW7

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

SW8

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

PULSE/REV

400

800

1600

3200

6400

12800

25600

1000

2000

4000

5000

8000

10000

20000

25000

 

2) Standstill current setting

SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic current and ON meaning that standstill is set to be the same as the selected dynamic current.

3) Output current setting:

The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a setting

Closest to your motor’s required current

Output current (A)

SW1

SW2

SW3

PEAK

RMS

ON

ON

ON

1.00

0.71

OFF

ON

ON

1.46

1.04

ON

OFF

ON

1.91

1.36

OFF

OFF

ON

2.37

1.69

ON

ON

OFF

2.84

2.03

OFF

ON

OFF

3.31

2.36

ON

OFF

OFF

3.76

2.69

OFF

OFF

OFF

4.20

3.00

 

4) Semi-flow  function:

Semi-flow function is that there is not step pulse after 500 ms, the driver output current automatically reduced to 70% of rated output current, which is used to prevent motor heat.

4. Pins of motor & power:

Motor and power pins

1

A+

Motors wiring

2

A-

3

B+

4

B-

5,6

DC+ DC-

Power supply Power supply :DC18-50VDC

5. Mechanical Specification:

To have 20mm of space around, cannot be placed next to other heating devices. Whats more,  avoid dust, oil mist, corrosive gas, heavy humidity and high vibration

t3

6. Adjustment of troubleshooting

1) , the status on light’s indication
PWR: green, normal work light.
ALM: red, failure light, the motor with phase short-circuit, overvoltage and under-voltage  protection.

2) Troubles

Alarm indicator  Reasons Measures
LED off turn Wrong connection for power Check wiring of power
Low-voltages for power Enlarge voltage of power
Motor doesn’t run, without holding torque Wrong connection of stepper motor Correct its wiring
RESET signal is  effective when offline Make RESET ineffective
Motor doesn’t run, but maintains holding torque Without input pulse signal Adjust PMW & signal level
Motor runs wrong direction

Wrong wires’ connection

Change connection for any of 2 wires

Wrong input direction signal Change direction setting
Motor’s holding torque is too small Too small relative to current setting Correct rated current setting
Acceleration is too fast Reduce the acceleration
Motor stalls Rule out mechanical failure
Driver does not match with the motor Change a suitable driver

 

7. Driver wiring
A complete stepper motor control system should contain stepper drives, DC power supply and controller (pulse source). The following is a typical system wiring diagram

t4

 


Product detail pictures:

Chinese Professional Stepper Motor 2 Phase -
 stepper motor driver-DM542A – Longs Motor detail pictures


Related Product Guide:
How to Troublshoot Servo Motors and Stepper Motors
CNC Stepper Motors

We're convinced that with joint endeavours, the business between us will bring us mutual benefits. We are able to guarantee you products high quality and competitive value for Chinese Professional Stepper Motor 2 Phase - stepper motor driver-DM542A – Longs Motor, The product will supply to all over the world, such as: Estonia , Thailand , Dubai , Really should any of these items be of interest to you, please let us know. We will be pleased to give you a quotation upon receipt of one's detailed specifications. We've our personal specialist R&D enginners to meet any of the requriements, We look forward to receiving your enquires soon and hope to have the chance to work together with you inside the future. Welcome to take a look at our organization.
  • The customer service reprersentative explained very detailed, service attitude is very good, reply is very timely and comprehensive, a happy communication! We hope to have a opportunity to cooperate.
    5 Stars By Stephanie from United States - 2016.09.28 18:29
    Speaking of this cooperation with the Chinese manufacturer, I just want to say"well dodne", we are very satisfied.
    5 Stars By John from Boston - 2016.11.12 12:31
    WhatsApp Online Chat !