OEM Supply 24v Dc Driver - DRIVER-BLDC-8015A – Longs Motor

Product Detail

Product Tags

Related Video

Feedback (2)

Our commission should be to provide our customers and consumers with ideal top quality and aggressive portable digital products for High Quality Stepper Motor 5v , Dc Motor 20kw , Closed Loop Motor 23ssm8440-Ec1000 , If possible, please send your requirements with a detailed list including the style/item and quantity you require. We will then send our best prices to you.
OEM Supply 24v Dc Driver - DRIVER-BLDC-8015A – Longs Motor Detail:

Features

SPWM,Speed/Current alike close loop technology, smooth rotation

Smooth torque output within speed range (8000 rpm Max.)

1:75 Max. speed regulation ratio

60°/300°/120°/240°Electrical angle adjustable

Speed regulation: potentiometer adjust / Analog input

Run/Step、Quick Brake、CW/CCW rotation shift

Speed output、Alarm output(O.C.)

Over current、over voltage、stall、missing speed Alarm

 

Parameters

Electrical ParametersTj25ºC

Power

24~50VDC, Capacity:up to motors

Current output

Rated 15A,Peak 45A(≤3s)

Driving mode

SPWM

Insulation Res.

>500MΩ

Dielectric Strength

500V/Minute

Weight

About 300g

Ambient requirement

Cooling

Self cool

Environment

Keep away from oil, dust, and acid gas

Temperature

0ºC~+50ºC

Humidity

<80%RH

Vibration

5.7m/s2Max.

Storage temp.

-20ºC~+125ºC

 

Function description

Power Supply: DC+ ; DC-

Voltage: 24~50DC,normally Linear Power Supply applied(appendix),ripple voltage higher than 50V may damage driver. The output current of LPS shall be 60%more than that of driver. In case of switching power supply(strongly recommended)applied, please pay attention to the current shall meet motor’s current.

Attention: incorrect connection may cause driver damaged.

Speed regulation choice(RV ; AVI)

1.          Setup speed by potentiometer (RV).The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. CCW- speed down.

2.          Setup speed by analog input (AVI). The dipswitch SW2 must be OFF status to enable this function.。AVI terminal accept 0~5V voltage or PWM signal from controller。AVI terminal with input resistance of 100K,current consumption≤5mA。

Reference table

SW2

Command to

Speed adjust

Comman

Current

ON

RV

CW—speed up,CCW—speed down

OFF

AVI

0~5V analog input

0~5V volage

≤5mA

OFF

AVI

PWM

1KHz duty cycle

  Only one of above two modes can be used to adjust speed (another mode shall be enabled). Once AVI terminal applied, (RV) potentiometer shall be CCW turned to Min. positionPWM signal are 5V TTL level.

 Run/StopENBL

ENBL terminal is applied to control motor Run/Stop,Common positive terminal is +5V.

Optical coupler short circuit make motor run, it open circuit make motor stop.

See below circuit
a2

CW/CCW RotationF/R

F/R terminal is applied to shift motor rotate direction, common positive terminal is+5V.

Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit.

Attentiondon’t change the connection sequence of phase wires of motor to shift rotate direction.
l   Motor Brake CommandBRK

BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms. But inertia of load can’t exceed 2 times of motor inertia, otherwise brake will cause driver alarm.

Time of acceleration and deceleration must be put into controller in case of too big load inertia,

And please don’t use brake function in such condition.

The optical coupler short circuit will brake motor,optical coupler open circuit release motor to run.

Setup different electrical angle

Dipswitch SW1 can be setup to fit motors with different electrical angel

SW1

ON

120°or 240°hall signal,they are in opposite rotation direction

OFF

60°or 300°hall signal, they are in opposite rotation direction

 

Motor rotation speed outputSPEED

Pulse generated by driver are proportioned with motor speed,(isolated O.C. output) it can be increased to be a random level. 6 multiple frequency processed output.

Motor speed=60×SPEED(pulse freq.)/pulses per rev. of motor;p.p.r=motor pole pairs×6

a3

Alarm output(ALM

Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL arise,LED on driver will be light, and ALM signal will be available. Please cut off

driver’s power supply,check wiring and voltage. High voltage is not permitted for big inertia motor, as it may cause run/stop frequently and over voltage alarm.  Circuit of this function refer to pic. 2.

Terminals description

Terminal mark

Description

DC+DC-

Voltage supply to driver

UVW

To motor leads. Make sure correct connection to motor leads.

REF+REF-HUHVHW

Hall sensor connection,REF+;REF- are for hall power supply. Make sure correct connection to halls.

AVIENBLF/RBRKVcc

Controls input,see below picture

SPEEDALM

Signal output,(O.C.)

a4

 

a5

a6

 

VDC+≈1.414×Vout,    Vout suggested to be AC2128V for this driver

Capacity of transformer shall be decided by motor’s current

C1=100V/2200uFC2=400V/0.22 uF

 


Product detail pictures:

OEM Supply 24v Dc Driver -
 DRIVER-BLDC-8015A – Longs Motor detail pictures


Related Product Guide:
Finding Inexpensive Stepper Motors
CNC Stepper Motors

Good quality comes to start with; service is foremost; organization is cooperation" is our enterprise philosophy which is regularly observed and pursued by our firm for OEM Supply 24v Dc Driver - DRIVER-BLDC-8015A – Longs Motor, The product will supply to all over the world, such as: Russia , Brazil , Manila , We welcome you to visit our company & factory and our showroom displays various products that will meet your expectations. Meanwhile, it is convenient to visit our website. Our sales staff will try their best to provide you with the best services. If you need more information, please do not hesitate to contact us via E-mail, fax or telephone.
  • The customer service staff is very patient and has a positive and progressive attitude to our interest, so that we can have a comprehensive understanding of the product and finally we reached an agreement, thanks!
    5 Stars By Alma from Mali - 2018.02.21 12:14
    It's really lucky to find such a professional and responsible manufacturer, the product quality is good and delivery is timely, very nice.
    5 Stars By Elaine from Macedonia - 2018.09.23 17:37
    WhatsApp Online Chat !