DRIVER-BLDC-8015A

  • FOB Price: US $0.5 - 9,999 / Piece
  • Min.Order Quantity: 100 Piece/Pieces
  • Supply Ability: 10000 Piece/Pieces per Month
  • Port: Shenzhen
  • Payment Terms: L/C,D/A,D/P,T/T
  • Product Detail

    Product Tags

    Features

    SPWM,Speed/Current alike close loop technology, smooth rotation

    Smooth torque output within speed range (8000 rpm Max.)

    1:75 Max. speed regulation ratio

    60°/300°/120°/240°Electrical angle adjustable

    Speed regulation: potentiometer adjust / Analog input

    Run/Step、Quick Brake、CW/CCW rotation shift

    Speed output、Alarm output(O.C.)

    Over current、over voltage、stall、missing speed Alarm

     

    Parameters

    Electrical ParametersTj25ºC

    Power

    24~50VDC, Capacity:up to motors

    Current output

    Rated 15A,Peak 45A(≤3s)

    Driving mode

    SPWM

    Insulation Res.

    >500MΩ

    Dielectric Strength

    500V/Minute

    Weight

    About 300g

    Ambient requirement

    Cooling

    Self cool

    Environment

    Keep away from oil, dust, and acid gas

    Temperature

    0ºC~+50ºC

    Humidity

    <80%RH

    Vibration

    5.7m/s2Max.

    Storage temp.

    -20ºC~+125ºC

     

    Function description

    Power Supply: DC+ ; DC-

    Voltage: 24~50DC,normally Linear Power Supply applied(appendix),ripple voltage higher than 50V may damage driver. The output current of LPS shall be 60%more than that of driver. In case of switching power supply(strongly recommended)applied, please pay attention to the current shall meet motor’s current.

    Attention: incorrect connection may cause driver damaged.

    Speed regulation choice(RV ; AVI)

    1.          Setup speed by potentiometer (RV).The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. CCW- speed down.

    2.          Setup speed by analog input (AVI). The dipswitch SW2 must be OFF status to enable this function.。AVI terminal accept 0~5V voltage or PWM signal from controller。AVI terminal with input resistance of 100K,current consumption≤5mA。

    Reference table

    SW2

    Command to

    Speed adjust

    Comman

    Current

    ON

    RV

    CW—speed up,CCW—speed down

    OFF

    AVI

    0~5V analog input

    0~5V volage

    ≤5mA

    OFF

    AVI

    PWM

    1KHz duty cycle

      Only one of above two modes can be used to adjust speed (another mode shall be enabled). Once AVI terminal applied, (RV) potentiometer shall be CCW turned to Min. positionPWM signal are 5V TTL level.

     Run/StopENBL

    ENBL terminal is applied to control motor Run/Stop,Common positive terminal is +5V.

    Optical coupler short circuit make motor run, it open circuit make motor stop.

    See below circuit
    a2

    CW/CCW RotationF/R

    F/R terminal is applied to shift motor rotate direction, common positive terminal is+5V.

    Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit.

    Attentiondon’t change the connection sequence of phase wires of motor to shift rotate direction.
    l   Motor Brake CommandBRK

    BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms. But inertia of load can’t exceed 2 times of motor inertia, otherwise brake will cause driver alarm.

    Time of acceleration and deceleration must be put into controller in case of too big load inertia,

    And please don’t use brake function in such condition.

    The optical coupler short circuit will brake motor,optical coupler open circuit release motor to run.

    Setup different electrical angle

    Dipswitch SW1 can be setup to fit motors with different electrical angel

    SW1

    ON

    120°or 240°hall signal,they are in opposite rotation direction

    OFF

    60°or 300°hall signal, they are in opposite rotation direction

     

    Motor rotation speed outputSPEED

    Pulse generated by driver are proportioned with motor speed,(isolated O.C. output) it can be increased to be a random level. 6 multiple frequency processed output.

    Motor speed=60×SPEED(pulse freq.)/pulses per rev. of motor;p.p.r=motor pole pairs×6

    a3

    Alarm output(ALM

    Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL arise,LED on driver will be light, and ALM signal will be available. Please cut off

    driver’s power supply,check wiring and voltage. High voltage is not permitted for big inertia motor, as it may cause run/stop frequently and over voltage alarm.  Circuit of this function refer to pic. 2.

    Terminals description

    Terminal mark

    Description

    DC+DC-

    Voltage supply to driver

    UVW

    To motor leads. Make sure correct connection to motor leads.

    REF+REF-HUHVHW

    Hall sensor connection,REF+;REF- are for hall power supply. Make sure correct connection to halls.

    AVIENBLF/RBRKVcc

    Controls input,see below picture

    SPEEDALM

    Signal output,(O.C.)

    a4

     

    a5

    a6

     

    VDC+≈1.414×Vout,    Vout suggested to be AC2128V for this driver

    Capacity of transformer shall be decided by motor’s current

    C1=100V/2200uFC2=400V/0.22 uF

     


  • Previous:
  • Next:

  • WhatsApp Online Chat !